User Contributed MET/CAL PROCEDURE ============================================================================= INSTRUMENT: Fluke 702 Sub 4 DATE: 29-Aug-97 AUTHOR: User Contributed REVISION: ADJUSTMENT THRESHOLD: 70% NUMBER OF TESTS: 38 NUMBER OF LINES: 323 CONFIGURATION: HP 34401A CONFIGURATION: HP 5335A CONFIGURATION: Datron 1281 STANDARD: Stanford Research FS700 ============================================================================= STEP FSC RANGE NOMINAL TOLERANCE MOD1 MOD2 3 4 CON 1.001 ASK- P F V 1.002 ASK+ K X 1.003 HEAD {* FREQUENCY SOURCE TEST *} 1.004 STD Stanford Research FS700 1.005 JMP 2.001 1.006 EVAL # 2.001 DISP Press CURSOR DATA and then the FUNCTION soft key # 2.001 DISP on the ScopeMeter. # 2.002 DISP Use the arrow buttons to select PEAK/PEAK. # 2.002 DISP # 2.002 DISP If not already enabled, press the ENTER soft key # 2.002 DISP to enable PEAK/PEAK display. # 2.002 DISP # 2.002 DISP Press the FUNCTION soft key to remove the menu. # 2.003 PIC 58_70x_V 2.001 DISP [32] Connect the UUT and the 5335A as follows. 2.001 DISP [32] 702 TO 5335A 2.001 DISP [32] OUTPUT V HI ÄÄÄÄÄÄÄÄÄ INPUT A HI 2.001 DISP [32] OUTPUT V LO ÄÄÄÄÄÄÄÄÄ INPUT A LO # 2.004 DISP Connect the ScopeMeter CHANNEL A Input to the UUT # 2.004 DISP V SOURCE HI & LO using a BNC cable and a BNC to dual # 2.004 DISP banana adapter. 2.002 IEEE [@5335] [TERM LF] 2.003 IEEE [@5335] IN[D2000]; 2.004 IEEE [@5335] FN12,AU1; 2.005 DISP Press VAC to select VAC Source on the UUT. 2.006 DISP Press ENTER to select 1.000V. 2.007 DISP Press 5 and then ENTER for 5Hz. # 2.008 DISP Press AUTO SET on the ScopeMeter. # 2.009 DISP Set the ScopeMeter to 100ms/DIV and Ch A to DC coupling. # 2.010 EVAL Is the ScopeMeter displaying a {50% duty cycle square wave}? 2.008 IEEE [@5335] [I] 2.009 MATH MEM1 = 50 2.010 MEME 2.011 MEMC duty_cy % 1U #! T.U.R. not calculated because System Uncertainty not available. 3.001 IEEE [@5335] FN1,AU1,AF1; 3.002 IEEE [@5335] [I] 3.003 MATH MEM1 = 5 3.004 MEME 3.005 MEMC H 0.01U 1V #! T.U.R. not calculated because System Uncertainty not available. 4.001 DISP Disconnect the test setup. 4.002 IEEE [@1281]ACV AUTO,ACCP,FILT1HZ,TFER_OFF 4.003 DISP [32] Connect the 1281 and the UUT as follows. 4.003 DISP [32] 702 TO 1281 4.003 DISP [32] OUTPUT V HI ÄÄÄÄÄÄÄÄÄ INPUT HI 4.003 DISP [32] OUTPUT V LO ÄÄÄÄÄÄÄÄÄ INPUT LO 4.004 IEEE [@1281]RDG?[T0][I] 4.005 ACC 2 1.000Vp 170P% 60P/ 4.006 MEM* 2 4.007 MEME 4.008 MEMC Vp 0.080U 5H #! Test Tol 0.08, Sys Tol 0.00029, TUR 275.862 (>= 4.00). # 4.001 3458 5.00H 0.01U 1V 2W 5.001 IEEE [@1281]ACV AUTO,FILT100HZ,TFER_OFF 5.002 DISP Press 500 and then ENTER for 500Hz. # 5.004 DISP Press AUTO SET on the ScopeMeter. # 5.005 MEMI Enter ScopeMeter P/P value in millivolts: # 5.006 MATH MEM = MEM / 1000 # 5.007 MEMC 1.000Vp 0.150U 500H 5.003 IEEE [@1281]RDG?[D2000][I] # 5.004 ACC 2 1.000Vp 130P% 10P/ 5.004 MEM* 2 5.005 MEME 5.006 MEMC Vp 0.080U 500H #! Test Tol 0.08, Sys Tol 0.00015, TUR 533.333 (>= 4.00). # 7.001 3458 500H 1U 1V 2W 6.001 IEEE [@1281]FREQ?[D2000][I] 6.002 ACC 500H 10P% 6.003 MEME 6.004 MEMC H 1U 1V #! Test Tol 1, Sys Tol 0.005, TUR 200.000 (>= 4.00). 7.001 DISP Press 50, the kHz soft key, and then ENTER for 50kHz. # 7.002 DISP Press AUTO SET on the ScopeMeter. # 7.003 MEMI Enter ScopeMeter P/P value in millivolts: # 7.004 MATH MEM = MEM / 1000 # 7.005 MEMC 1.000Vp 0.350U 50kH # 8.001 3458 50kH 2U 1V 2W 7.002 IEEE [@1281]DCCP 7.003 IEEE [@1281]ACV AUTO,DCCP,TFER_OFF[D2000] 7.004 IEEE [@1281]RDG?[D2000][I] 7.005 ACC 2 1.000Vp 250P% 20P/ 7.006 MEM* 2 7.007 MEME 7.008 MEMC Vp 0.350U 50kH #! Test Tol 0.35, Sys Tol 0.00029, TUR 1206.897 (>= 4.00). # 7.001 3458 500H 1U 1V 2W 8.001 IEEE [@1281]FREQ?[D2000][I] 8.002 MEM/ 1000 8.003 ACC 50kH 10P% 8.004 MEME 8.005 MEMC kH 2U 1V #! Test Tol 2, Sys Tol 0.0005, TUR 4000.000 (>= 4.00). 9.001 DISP Press CLEAR (ZERO) twice to turn off the output. 9.002 DISP Disconnect the test setup. 9.003 HEAD {* VOLTS DC SOURCE TEST *} 9.004 HEAD {110mV Range} 9.005 JMP 10.001 9.006 EVAL 10.001 DISP Press VDC to select VDC Source. #10.002 IEEE [@1281] DCV AUTO 10.002 DISP Press -10, the mV soft key, and then ENTER for 10.002 DISP -10.000mV. 10.003 34401 -10.000mV 0.010U 2W #11.001 IEEE [@1281] RDG?[D2000][I] #11.002 MEM* 1000 #11.003 ACC 200 -10.000mV 7P% 5P/ #11.004 MEME #11.005 MEMC mV 0.010U #! Test Tol 0.01, Sys Tol 0.00107, TUR 9.346 (>= 4.00). 11.001 DISP Press 100 and then ENTER for 100.000mV. 11.002 34401 100.000mV 0.028U 2W #12.002 IEEE [@1281] RDG?[D2000][I] #12.003 MEM* 1000 #12.004 ACC 200 100.000mV 7P% 5P/ #12.005 MEME #12.006 MEMC mV 0.028U #! Test Tol 0.028, Sys Tol 0.0017, TUR 16.471 (>= 4.00). 12.001 HEAD VOLTS DC SOURCE: {1.1V Range} 12.002 JMP 13.001 12.003 EVAL 13.001 DISP Press 120 and then ENTER for 0.12000V. 13.002 34401 0.12000V 0.00008U 2W #14.002 IEEE [@1281] RDG?[D2000][I] #14.003 ACC 2 0.12000V 6P% 0.2P/ #14.004 MEME #14.005 MEMC V 0.00008U #! Test Tol 8e-005, Sys Tol 1.12e-006, TUR 71.429 (>= 4.00). 14.001 DISP Press 1, the V soft key, and then ENTER for 1.00000V. 14.002 34401 1.00000V 0.00025U 2W #15.002 IEEE [@1281] RDG?[D2000][I] #15.003 ACC 2 1.0000V 6P% 0.2P/ #15.004 MEME #15.005 MEMC V 0.00025U #! Test Tol 0.00025, Sys Tol 6.4e-006, TUR 39.062 (>= 4.00). 15.001 HEAD VOLTS DC SOURCE: {11V Range} 15.002 JMP 16.001 15.003 EVAL 16.001 DISP Press 1.2 and then ENTER for 1.2000V. 16.002 34401 1.2000V 0.0008U 2W #17.002 IEEE [@1281] RDG?[D2000][I] #17.003 ACC 2 1.2000V 6P% 0.2P/ #17.004 MEME #17.005 MEMC V 0.0008U #! Test Tol 0.0008, Sys Tol 7.6e-006, TUR 105.263 (>= 4.00). 17.001 DISP Press 10 and then ENTER for 10.0000V. 17.002 34401 11 10.0000V 0.0026U 2W #18.002 IEEE [@1281] RDG?[D2000][I] #18.003 ACC 20 10.0000V 6P% 0.1P/ #18.004 MEME #18.005 MEMC V 0.0026U #! Test Tol 0.0026, Sys Tol 6.2e-005, TUR 41.935 (>= 4.00). 18.001 DISP Press CLEAR (ZERO) twice to turn off the output. 18.002 DISP Disconnect the test setup. 18.003 HEAD {* OHMS SOURCE TEST *} 18.004 HEAD {11 Ohm Range} 18.005 JMP 19.001 18.006 EVAL #18.001 PIC 42_70xCW 19.001 DISP [32] Connect the UUT and the 1281 as follows. 19.001 DISP [32] 702 TO 1281 19.001 DISP [32] OUTPUT V RTD HI ÄÄÄÄÄÄÄÄÄ INPUT HI 19.001 DISP [32] OUTPUT V RTD LO ÄÄÄÄÄÄÄÄÄ INPUT LO 19.001 DISP [32] OUTPUT V RTD HI ÄÄÄÄÄÄÄÄÄ I + 19.001 DISP [32] OUTPUT V RTD LO ÄÄÄÄÄÄÄÄÄ I - #20.002 IEEE [@1281]TRUE_OHMS AUTO 19.002 DISP Press OHMS/CONTINUITY to select Ohms Source. 19.003 DISP Press .1 and then ENTER for 0.100 Ohms. 19.004 34401 0.100Z 0.050U 4W #20.005 IEEE [@1281] RDG?[D2000][I] #20.006 ACC 20 0.100Z 13P% 1P/ #20.007 MEME #20.008 MEMC Z 0.050U #! Test Tol 0.05, Sys Tol 2.13e-005, TUR 2347.418 (>= 4.00). 20.001 DISP Press 1 and then ENTER for 1.000 Ohms. 20.002 34401 1.000Z 0.050U 4W #21.002 IEEE [@1281] RDG?[D2000][I] #21.003 ACC 20 1.000Z 13P% 1P/ #21.004 MEME #21.005 MEMC Z 0.050U #! Test Tol 0.05, Sys Tol 3.3e-005, TUR 1515.152 (>= 4.00). 21.001 DISP Press 10 and then ENTER for 10.000 Ohms. 21.002 34401 10.000Z 0.052U 4W #22.002 IEEE [@1281] RDG?[D2000][I] #22.003 ACC 20 10.000Z 13P% 1P/ #22.004 MEME #22.005 MEMC Z 0.052U #! Test Tol 0.052, Sys Tol 0.00015, TUR 346.667 (>= 4.00). 22.001 HEAD OHMS SOURCE: {110 Ohm Range} 22.002 JMP 23.001 22.003 EVAL 23.001 DISP Press 20 and then ENTER for 20.00 Ohms. 23.002 34401 20.00Z 0.05U 4W #24.002 IEEE [@1281] RDG?[D2000][I] #24.003 ACC 200 20.00Z 11P% 0.3P/ #24.004 MEME #24.005 MEMC Z 0.05U #! Test Tol 0.05, Sys Tol 0.00028, TUR 178.571 (>= 4.00). 24.001 DISP Press 100 and then ENTER for 100.00 Ohms. 24.002 34401 100.00Z 0.07U 4W #25.002 IEEE [@1281] RDG?[D2000][I] #25.003 ACC 200 100.00Z 11P% 0.3P/ #25.004 MEME #25.005 MEMC Z 0.07U #! Test Tol 0.07, Sys Tol 0.00116, TUR 60.345 (>= 4.00). 25.001 HEAD OHMS SOURCE: {1.1 kOhm Range} 25.002 JMP 26.001 25.003 EVAL 26.001 DISP Press 200 and then ENTER for 200.0 Ohms. 26.002 34401 0.2000kZ 0.0006U 4W #27.002 IEEE [@1281] RDG?[D2000][I] #27.003 MEM/ 1000 #27.004 ACC 2 .2000kZ 14P% 0.7P/ #27.005 MEME #27.006 MEMC kZ 0.0006U #! Test Tol 0.0006, Sys Tol 4.2e-006, TUR 142.857 (>= 4.00). 27.001 DISP Press 1000 and then ENTER for 1000.0 Ohms. 27.002 34401 1.0000kZ 0.0010U 4W #28.002 IEEE [@1281] RDG?[D2000][I] #28.003 MEM/ 1000 #28.004 ACC 2 1.0000kZ 14P% 0.7P/ #28.005 MEME #28.006 MEMC kZ 0.0010U #! Test Tol 0.001, Sys Tol 1.54e-005, TUR 64.935 (>= 4.00). 28.001 HEAD OHMS SOURCE: {11 kOhm Range} 28.002 JMP 29.001 28.003 EVAL 29.001 DISP Press 2, the kOhm soft key, and then ENTER for 29.001 DISP 2.000 kOhms. 29.002 34401 2.000kZ 0.007U 4W #30.002 IEEE [@1281] RDG?[D2000][I] #30.003 MEM/ 1000 #30.004 ACC 20 2.000kZ 28P% 4.0P/ #30.005 MEME #30.006 MEMC kZ 0.007U #! Test Tol 0.007, Sys Tol 0.000136, TUR 51.471 (>= 4.00). 30.001 DISP Press 10 and then ENTER for 10.000 kOhms. 30.002 34401 10.000kZ 0.015U 4W #31.002 IEEE [@1281] RDG?[D2000][I] #31.003 MEM/ 1000 #31.004 ACC 20 10.000kZ 28P% 4.0P/ #31.005 MEME #31.006 MEMC kZ 0.015U #! Test Tol 0.015, Sys Tol 0.00036, TUR 41.667 (>= 4.00). 31.001 DISP Press CLEAR (ZERO) twice to turn off the output. 31.002 HEAD {* RTD SOURCE TEST *} 31.003 JMP 32.001 31.004 EVAL 32.001 DISP Press the TC/RTD button twice to select RTD Source. 32.002 DISP Use the arrow buttons to select Pt100 (385) and then 32.002 DISP press ENTER. 32.003 DISP Press -180 and then ENTER for -180degC. 32.004 34401 27.05Z 0.15U 4W #33.004 IEEE [@1281] RDG?[D2000][I] #33.005 ACC 20 27.05Z 13P% 1P/ #33.006 MEME #33.007 MEMC Z 0.15U #! Test Tol 0.15, Sys Tol 0.00037165, TUR 403.606 (>= 4.00). 33.001 DISP Press 100 and then ENTER for 100degC. 33.002 34401 138.45Z 0.15U 4W #34.002 IEEE [@1281] RDG?[D2000][I] #34.003 ACC 200 138.45Z 11P% 0.3P/ #34.004 MEME #34.005 MEMC Z 0.15U #! Test Tol 0.15, Sys Tol 0.001583, TUR 94.760 (>= 4.00). 34.001 DISP Press 310 and then ENTER for 310degC. 34.002 34401 215.55Z 0.25U 4W #35.002 IEEE [@1281] RDG?[D2000][I] #35.003 MEM/ 1000 #35.004 ACC 2 .21555kZ 14P% 0.7P/ #35.005 MEME #35.006 MEMC kZ 0.00025U #! Test Tol 0.00025, Sys Tol 4.4177e-006, TUR 56.591 (>= 4.00). 35.001 DISP Press CLEAR (ZERO) twice to turn off the output. 35.002 DISP Disconnect the 1281 from the UUT. 35.003 HEAD {* LOOP POWER TEST *} 35.004 JMP 36.001 35.005 EVAL 36.001 PIC 58_70xLP #37.002 IEEE [@1281] DCV AUTO 36.002 DISP [32] Connect the UUT and the 1281 as follows. 36.002 DISP [32] 702 TO 1281 36.002 DISP [32] OUTPUT mA HI ÄÄÄÄÄÄÄÄÄ INPUT HI 36.002 DISP [32] OUTPUT mA LO ÄÄÄÄÄÄÄÄÄ INPUT LO 36.003 DISP Press SETUP and then ENTER. 36.004 DISP Use the arrow buttons to select Enabled 24V and 36.004 DISP then press ENTER. 36.005 34401 24.00V 1.2U 2W #37.006 IEEE [@1281] RDG?[D2000][I] #37.007 ACC 200 24.00V 10P% 0.2P/ #37.008 MEME #37.009 MEMC V 1.2U #! Test Tol 1.2, Sys Tol 0.00028, TUR 4285.714 (>= 4.00). 37.001 DISP Press ENTER. 37.002 DISP Use the arrow buttons to select Enabled 28V and 37.002 DISP then press ENTER. 37.003 34401 28.00V 1.4U 2W #38.003 IEEE [@1281] RDG?[D2000][I] #38.004 ACC 200 28.00V 10P% 0.2P/ #38.005 MEME #38.006 MEMC V 1.4U #! Test Tol 1.4, Sys Tol 0.00032, TUR 4375.000 (>= 4.00). 38.001 DISP Press ENTER. 38.002 DISP Use the arrow buttons to select Disabled and 38.002 DISP then press ENTER. #33.003 DISP Press SETUP. 38.003 END